UPVC Window Repairs

Upvc windows are energy efficient and can help to reduce heating bills. As they age, however, problems can occur that need to be addressed. This could include damaged handles, hinges, or locks.

DIY people can fix wooden windows with ease. It's less expensive than buying a brand new window.

Cracks

Cracks and tears in uPVC windows can be a major issue. If they are not repaired, they can result in water infiltration as well as less effective barriers against cold temperatures and the risk of structural damage. It is essential to locate an expert local builder or repair service that specializes in fixing uPVC frames and who has the experience, skills and tools required to deliver the most effective results. This will ensure that your crack is repaired before it gets any worse and that you don't need to replace your window glass or window unit.

Small cracks in glass can be repaired with a range of home-based solutions. Masking tape and superglue are two of the most common products to hold cracked glass in position for a short duration. For more severe cracks, the tape may need to extend past the crack on both sides to achieve the best results.

Another option is two-part epoxy that can be used to repair broken or cracked glass. It's available at a lot of hardware stores and can be purchased for about $10. Make sure your workspace is prepared before mixing the epoxy. Also, ensure you have all the tools required for the job.

If your upper or lower sash isn't lifting easily it's most likely due to the fact that the cords on the sash weights are damaged. It's an easy fix that can be made using the ladder and a flathead screwdriver. Replacing a rotted drip cap is a different repair that is done at home. Drain caps that are free of rot are available at most home centers and can be nailed or caulked in place with ease. If you have a double glazed window repairs- or triple-paned window, be sure to check that one of the panes is not broken. The reason is because the gasses in the space between the windows are responsible for increasing the efficiency of the window. They must not escape.

Water Leaks

If your uPVC windows are leaking, it can ruin the interior of your house and cause costly repairs. Water leaks can also damage the structure of your home and can cause mold growth. To avoid damage, it's crucial to repair any issues caused by leaky windows immediately.

A damaged sealant around window frames is a typical cause of leaks. Utilizing silicone caulk can help restore the condition of the seal back to its normal condition and stop water leakage. Check for cracks and gaps around the window frame and also the stone or brick wall that surrounds your windows.

Another reason that can cause leaks in windows is a blocked drainage hole or faulty flashing. It is important to ensure that the drainage holes are free and unclogged, especially in the aftermath of a heavy downpour. It's also recommended to examine the flashing around the top of your window and ensure it's sealed correctly.

Finally, it's essential to check that your drip cap isn't missing or damaged. A rotten drip cap or one that's not there will allow water from above to enter your window and cause structural damage. Replacing the drip cap isn't an arduous task, and it's typically a simple task of purchasing the new one and nailing it into place.

A professional can also check your windows for watertightness. They can use a tool to test the water-tightness of your windows and ensure that they meet industry standards. If your windows fail the test, they'll have to be replaced. It's a costly repair however it's is worth it to ensure the safety and comfort of your family.

Sagging

If your windows aren't closing properly it can cause many problems, such as drafts, UPVC Window Repairs condensation and an increase in energy bills. It could also indicate that the windows were not properly installed or the sealant has worn away. There are fortunately, a few things you can do to correct the issue.

To fix your window properly it is essential to create a space with plenty of natural light. Begin by placing newspaper or an old blanket on the floor to shield it from drips or splinters that could be leaking from the window while you work.

Use a white cloth that has been soaked in a mix of water and detergent. This will ensure you don't leave any stains of color on your windows. If you're ready to work on your uPVC windows, begin by marking the location where the hinge channel needs to be located. Unscrew the channel and fill the screw holes in the frame using epoxy (for uPVC frames) or wood filler. Make sure you smooth the hole that you have filled before it sets.

Reinstall the hinge channel after the holes are filled. Make sure it's centered on the window jamb. Also, make sure that you drill the new holes approximately a quarter inch from the original locations.

Then, take a measurement of the spindle that protrudes from the underside of your handle. You can request an replacement or take it to a hardware shop for a replacement. Then, remove the setscrew from the shaft. Smooth it down to allow the set screw to secure onto the shaft. Now, your uPVC window should shut smoothly.

Broken Hinges

If your uPVC window hinges have been damaged or aren't working properly then you'll find it difficult to open or close the window. This could cause problems with security and prevent your home from being warm or cool. You can easily purchase an entirely new hinge for your uPVC window. It is essential to select the right hinge for your windows.

The hinges must be identical in size to fit in the frame of the window. The most common hinge for uPVC windows is standard 18mm or UPVC 15mm window hinges. There are also specialised hinges for wooden frames. The correct type of hinge will allow you to avoid common issues with your windows.

There are many reasons why the hinges on your windows have become slack or stiff. One of the most common causes is that the hinges aren't sufficiently tightened. To test this, take a screwdriver and find the friction screw on the end of the hinge. Release it. You can then adjust it by turning it either way.

Contact Preston Glass Fix if your UPVC window's hinges don't work properly. We can offer an immediate fix. Our technicians will examine the condition of your hinges and give you suggestions on the best solution. We can repair or replace your window hinges, retension them or install new locking mechanisms to ensure that your UPVC Windows are safe and secure.

Locks that aren't working

UPVC window mechanisms and locks are an important part of home security. They make it difficult to open a window without breaking into the home. It can be a frustrating experience when a lock malfunctions, but you don't have to replace the entire window.

It's usually an issue that is minor and could have been easily prevented with regular maintenance. We suggest that you have your uPVC window serviced regularly as part of our annual maintenance package in order to minimize the chance of having any issues.

Modern uPVC windows come with espagnolette locks. They operate by putting the nose of the handle onto the wedge block, then turning it to close the lock. They are very efficient in keeping the window closed, however over time they can start to fail if not properly maintained. We recommend using WD-40 for lubrication a couple of times per year.

If you notice your uPVC window isn't opening or closing as easily as it did in the past, or if the lock doesn't function properly, there could be an issue with the locking gearboxes within the frame. This is often difficult to access since it requires removing the seals around the window frame and taking off the handle.