Reasons Your fiat 500 remote key programming 500 Key Fob Won't Work

A fiat 500 Spare key cost 500 key fob is a great way to open the doors and begin the car. There are a variety of reasons why the fob won't work. This includes a dead battery or water damage, problems with receiver modules, as well as interference.

This listing is for a NEW replacement fiat 500 key fob programming Flip Key Remote - similar to the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not functioning. Modern key fobs only have a limited range of operation and must be within a few inches of the vehicle to work. If you are not within your car and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the coin-cell battery (Part Number CR2032) by a fresh one from a reputable brand such as Panasonic Duracell or Energizer. You can find them at your local hardware store, or on the internet.

You can test the battery of your coin-cell by pressing the buttons while standing near your Fiat 500. The car should blink its parking lights, and the key fob should work the lock and unlock buttons.

If the key fob won't function after replacing the battery, it may have water damage that stops it from connecting to the receiver module inside your car. Water damage can happen in a variety of ways, from an accidental splash to submerging the fob salt water at the beach. If you suspect that your fob has been exposed to water, place it in a bag of rice to draw out the moisture. If that doesn't work, your fob may require reprogramming by a professional auto locksmith or the dealer.

Water Damage

Although the fob is equipped with rubber seals that keep water from the electronic chip inside, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and fiat 500 spare key cost eventually die. In the event that you let your fob get wet, it's not an ideal idea but if you accidentally drop it in a glass of water or forget to take it out of your pants pocket prior to running the washing machine Don't give up hope.

Take the battery off first. Clean the electronic chip using isopropyl alcohol or a similar product and then dry it completely before replacing the battery. Check the fob again to verify if it's working. If the fob doesn't work, it may have to be reprogrammed. This is usually done by a dealer or professional auto locksmith.

If the key is more recent and hasn't been programmed to your car, it will likely need to be replaced completely. This is a straightforward process which can be accomplished by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition of your vehicle. They will also need to reprogram the fob in your vehicle's system. This is a quick and inexpensive process which can be completed the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote usually has a range of 30 feet or less, and if it's too far from your car, it will not respond to your commands. This can be fixed by moving closer to your vehicle until it starts responding.

If your fob doesn't work after you replace the battery inside the coin, which is also known as a "button", "watch" or "button" It may be due to a malfunction on the circuit board inside. In most cases, reprogramming the fob will fix the problem. You can find the instructions for most vehicles on YouTube or in the owner's manual.

It is possible to replace the metal retaining clips that keep the coin battery in place. If they loose tension, it could hinder the battery from sitting properly, and this will cause your remote to malfunction.

In rare instances the fob might become disconnected from your vehicle due to software issues or hardware issues. This could cause a significant problem, but you can frequently fix this issue by visiting an auto locksmith to have them reprogram your fob. In some cases it is possible that the software will require reinstallation to your body control modules.

Interference

In addition to a dead coin battery The key fob may not be receiving or transmitting a signal due to interference. This could happen when the keyfob's location is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons why the key fob might not work may be a lack of connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or if you've tried everything at home to resolve it (e.g. replacing the battery, reprogramming, and using the spare key fob, you might have a defective receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts the signals into electronic commands, which are then translated by the vehicle.

There's a simple method to reset the 500's in-board system including the keyfob. Disconnect the battery of 12 volts for about 15 minutes, by disconnecting the negative cable first then the positive cable. Then reconnect the battery. This will eliminate any residual electricity and restart the car's computer system, which could help the key fob to function again. If the issue persists, you should consult an expert technician. They will be able to determine the exact cause of your problems.