Reasons Your fiat key cutting 500 Key Fob Won't Work

A key fob for the Fiat 500 allows you to easily open doors and start your car. However, there are a variety of reasons why the fob may stop working. It could be due to a dead battery or damage to the receiver module, water problems, and interference.

This listing is for a NEW replacement program fiat 500 key fob Flip Key Remote that appears similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths in the automotive industry). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent reason for your 500 key fob that isn't working. Modern key fobs have limited operating range and must be within only a few inches from the vehicle to work. If you're far from your vehicle, and you press the key fob button the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery of your coin cell (Part number CR2032) with a brand new one from a reputable brand like Panasonic, Duracell, or Energizer. You can typically find them in your local hardware store or on the internet.

After you've replaced the coin cell battery you can test it by standing close to your fiat Ducato key replacement 500 and pressing the buttons. The parking lights should blink and the key fob should operate the lock and unlock switch.

If the key fob doesn't work after replacing the battery, it might be damaged by water, which prevents it from connecting to the receiver module inside your vehicle. Water damage can occur in many ways, including simply splashing or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, put it in a dry rice bag to draw the moisture back out. If that doesn't work your fob is likely to need to be reset by a professional auto locksmith or dealer.

Water Damage

While the fob comes with rubber seals that keep water from the electronic chip inside it, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then end up dying. It's not good to submerge the fob in water however, but don't give it up in the event that you accidentally drop it in water or fail to remove it from your pants pocket.

First take the battery off the fob. Clean the electronic chip using isopropyl alcohol or a similar product and then dry it completely before replacing the battery. Test the fob next to verify if it's functioning. If the key does not function, it may need to be reprogrammed. This is usually handled by a professional or dealer auto locksmith.

If your key is a bit older and not programmed for your car then you'll need to replace it completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition of your car. The locksmith will also need to reprogram the fob into the vehicle's system. This is a cost-effective and quick process that can be completed the same day.

Receiver Module Issues

Your 500 key fob may stop working because it is out of range. The remote has a maximum range of 30 feet. Therefore, in the event that you are far away from your vehicle it won't be able to respond to your commands. You can fix this by moving the remote closer to your vehicle until it responds.

If you've replaced the battery on your coin (commonly called"button" or "button" or "watch") and your fob still won't work, Fiat ducato key replacement it could have an internal circuit board issue. In the majority of cases, reprogramming your fob will resolve this problem. You can find the instructions for the majority of vehicles on YouTube or in the owner's manual.

You may have to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension it could prevent the battery from being properly seated and could cause your remote to malfunction.

In rare instances, the fob may be out of connection with your vehicle as a result due to hardware or software issues. This could cause a significant problem, but you can usually resolve this issue by visiting an auto locksmith to have them reprogram your fob. In some cases they may have to reinstall the software in your body control module, too.

Interference

Interference can also cause the key fob not to receive or transmit an signal. This can happen when the key fob is in proximity to a radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob might not work may be a lack of connection to the buttons or the internal chip or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to resolve it (e.g. It could be a defective 500 receiver module If you've tried replacing it with a battery, reprogramming it, or using an alternative key fob. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It transforms the signals into electronic commands which are then read by the vehicle.

There is a simple way to reset the 500's on-board system, including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then, reconnect the battery. This will get rid of any remaining electricity and then restart the car's computers, which can help get your key fob working again. If the problem persists you should seek out an expert technician. They will be able to determine the root of any problems.